Manual de instruções Sony SNC-CS50N

Sony SNC-CS50N
  • Número de páginas: 2
  • Tipo de arquivo: PDF
  • 3-113-371-11 (1)
    2007 Sony Corporation Printed in China

    Network Camera

    Installation ManualBefore operating the unit, please read this manual thoroughlyand retain it for future reference.


    Owner’s Record

    The model and serial numbers are located on the bottom. Record these
    numbers in the spaces provided below.
    Refer to these numbers whenever you call upon your Sony dealer
    regarding this product.
    Model No.
    Serial No.


    To reduce a risk of fire or electric shock, do notexpose this product to rain or moisture.To avoid electrical shock, do not open the cabinet.Refer servicing to qualified personnel only.WARNING
    This installation should be made by a qualified service person and
    should conform to all local codes.
    A readily accessible disconnect device shall be incorporated in the
    building installation wiring.
    WARNING (for Installers only)
    Instructions for installing the equipment on the ceiling or the wall:
    After the installation, ensure the connection is capable of supporting at
    least a force of 50 Newtons (N) downwards.
    The rating label is located on the bottom.
    CAUTION for LAN port
    For safety reason, do not connect the LAN port to any network devices
    that might have excessive voltage.
    The LAN port of this unit is to be connected only to the devices whose
    power feeding meets the requirements for SELV (Safety Extra Low
    Voltage) and complies with Limited Power Source according to IEC
    Power SupplyCaution for U.S.A. and Canada
    The SNC-DF50N operates on 24 V AC or 12 V DC.
    The SNC-DF50N automatically detects the power.
    Use a Class 2 power supply which is UL Listed (in the U.S.A) or CSA-
    certified (in Canada).
    Caution for other countries
    The SNC-DF50N/DF50P operates on 24 V AC or 12 V DC.
    The SNC-DF50N/DF50P automatically detects the power.
    Use a power supply rated 24 V AC or 12 V DC which meets the
    requirements for SELV (Safety Extra Low Voltage) and complies with
    Limited Power Source according to IEC 60950-1.
    For customers in the U.S.A. (SNC-DF50N only)
    This device complies with Part 15 of the FCC Rules. Operation is
    subject to the following two conditions: (1) This device may not cause
    harmful interference, and (2) this device must accept any interference
    received, including interference that may cause undesired operation.
    NOTE: This equipment has been tested and found to comply with the
    limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
    These limits are designed to provide reasonable protection against
    harmful interference when the equipment is operated in a commercial
    environment. This equipment generates, uses, and can radiate radio
    frequency energy and, if not installed and used in accordance with the
    instruction manual, may cause harmful interference to radio
    communications. Operation of this equipment in a residential area is
    likely to cause harmful interference in which case the user will be
    required to correct the interference at his own expense.
    You are cautioned that any changes or modifications not expressly approved
    in this manual could void your authority to operate this equipment.
    All interface cables used to connect peripherals must be shielded in
    order to comply with the limits for a digital device pursuant to Subpart B
    of Part 15 of FCC Rules.
    For Customers in Canada (SNC-DF50N only)
    This Class A digital apparatus complies with Canadian ICES-003.
    Cet appareil numérique de la classe A est conforme à la norme NMB-
    003 du Canada.
    For customers in other countriesWARNING
    This is a Class A product. In a domestic environment, this product may
    cause radio interference in which case the user may be required to take
    adequate measures.
    In the case that interference should occur, consult your nearest
    authorized Sony service facility.
    The electromagnetic fields at specific frequencies may influence the
    picture of the unit.
    You should keep in mind that the images or audio you are
    monitoring may be protected by privacy and other legal rights, and
    the responsibility for making sure you are complying with
    applicable laws is yours alone.
    Access to the images and audio is protected only by a user name
    and the password you set up. No further authentication is provided
    nor should you presume that any other protective filtering is done
    by the service. Since the service is Internet-based, there is a risk
    that the image or audio you are monitoring can be viewed or used
    by a third-party via the network.
    This product is a network camera adopting the 1/3 type CCD. The camera has
    the following features:
    High sensitivity (minimum illumination: 0.7lx, F1.3)
    Automatic white balance tracking and adjustment (ATW/ATW-PRO)
    Manual setting of the camera direction – panning, tilting and rotating
    Vari-focal auto iris lens as standard equipment. The focal length of the
    lens is from 2.8 mm to 10 mm.
    High quality CCD and clear dome cover enable high sensitivity.
    Wide dynamic range (128 times wider than normal) using DynaView
    24 V AC / 12 V DC power supply system
    •3 video compression formats (video codecs) available: JPEG, MPEG4 and
    Single codec mode and dual codec mode switchable
    Up to 20 users can access an image of a camera simultaneously.
    You can monitor a high-quality live image of 30 frames per second maximum
    (SNC-DF50N) and 25 frames per second maximum (SNC-DF50P).
    Date/time can be superimposed on the image.
    Notes on Use
    Operating or storage location
    Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,
    avoid operating or storing the camera in the following locations, as these
    can be a cause of a malfunction.
    Extremely hot or cold places (Operating temperature: –10 °C to
    +50 °C [14 °F to 122 °F])
    Exposed to direct sunlight for a long time, or close to heating equipment
    (e.g., near heaters)
    Close to sources of strong magnetism
    Close to sources of powerful electromagnetic radiation, such as radios or
    TV transmitters
    Locations subject to strong vibration or shock
    Humid or dusty locations
    Locations exposed to rain
    Locations under the influence of fluorescent light or reflection of a window
    Under an unsteady light (the image will flicker.)
    To prevent heat buildup, do not block air circulation around the camera.
    When transporting the camera, repack it as originally packed at the factory
    or in materials of equal quality.
    Use a blower to remove dust from the lens.
    Use a soft, dry cloth to clean the external surfaces of the camera.
    Stubborn stains can be removed using a soft cloth dampened with a
    small quantity of detergent solution, then wipe dry.
    Do not use volatile solvents such as alcohol, benzene or thinners as they
    may damage the surface finishes.
    Note on laser beams
    Laser beams may damage a CCD. You are cautioned that the surface of a
    CCD should not be exposed to laser beam radiation in an environment where
    a laser beam device is used.
    Typical CCD Phenomena
    The following phenomena may appear on the monitor screen while you are
    using a CCD color video camera. These phenomena stem from the high
    sensitivity of the CCD image sensors, and do not indicate a fault within the
    Vertical smear
    A “smear” may appear to extend vertically from very bright subjects, as
    shown below.
    This phenomenon is common to CCD imaging elements using an interline
    transfer system, and is caused when electric charge induced by infrared
    radiation deep within the photo sensor is transferred to the resistors.
    When shooting fine stripes, straight lines or similar patterns, the lines may
    become slightly jagged.
    A CCD image sensor consists of an array of individual picture elements
    (pixels). A malfunctioning sensor element will show up
    as a single pixel blemish in the image. This is generally not a problem.
    White speckles
    When you shoot a poorly illuminated object at a high temperature, small
    white dots may appear all over the entire screen image.
    AB C
    Video monitor screen
    Pale vertical smear
    Very bright subject (such as an
    electric lamp, fluorescent lamp,
    sunlight, or strong reflected light)
    About the Supplied Manuals
    Names of Manuals
    The following manuals are supplied with this unit.
    Installation Manual (this document)
    The Installation Manual describes the names and functions of the parts of
    the camera, the installation and connections of the camera, etc. Be sure to
    read it before operating the camera.
    User’s Guide (stored in the CD-ROM)
    The User’s Guide describes the setup of the camera and the operations
    from the Web browser.
    To open the User’s Guide, see “Using the CD-ROM Manuals” below.
    Using the CD-ROM Manuals
    The supplied CD-ROM disc includes the User’s Guides for this unit
    (Japanese, English, French, German, Spanish, Italian and Chinese
    versions) in PDF format.
    The Adobe Reader Version 6.0 or higher must be installed on your
    computer in order to use the User’s Guide stored in the CD-ROM disc.
    If Adobe Reader is not installed, it may be downloaded from the following
    Reading the manual in the CD-ROM1 Insert the CD-ROM in your CD-ROM drive.
    A cover page appears automatically in your Web browser.
    If it does not appear automatically in the Web browser, double-click on
    the index.htm file on the CD-ROM.
    2 Select and click on the manual that you want to read.
    This opens the PDF file of the manual.
    Clicking an item in the Table of Contents allows you jump to the relevant
    The files may not be displayed properly, depending on the version of
    Adobe Reader. In this case, install the latest version, which you can
    download from the URL mentioned in “Preparations” above.
    If you have lost or damaged the CD-ROM, you can purchase
    replacement. Contact your Sony service representative.
    Adobe, Acrobat and Acrobat Reader are trademarks of Adobe Systems
    Incorporated in the United States and/or other countries.
    Location and Function of Part
    The figure shows the camera without the dome casing and the slit cover.
    1 Indoor wiring slit (knockout type)
    When you wire indoors, cut this part with a nipper or similar and feed the
    cable through it.
    Take care not to trap the cable between the camera and the ceiling or
    the wall. If the cable is trapped, it may cause a fire or electric shock due
    to breaking.
    2 Camera head holder
    3 Lens
    4 Lens ring fixing screw
    Loosen this screw before adjusting the zoom and focus, then tighten it to
    fix the lens position. The screw can be inserted at one of three points.
    5 Zoom ring
    Turn this ring to adjust the field of view.
    6 Focus ring
    Turn this ring to adjust the focus.
    7 Dome casing screw hole
    8 LAN indicator (green)
    This indicator flashes in green when the camera is connected to the
    network. The indicator goes off when the camera is not connected to the
    9 POWER indicator (green)
    When the power is supplied to the camera, the camera starts checking
    the system. If the system is normal, this indicator lights up.
    q; Reset switch
    To reset the camera to the factory default settings, hold down this switch
    with a point and supply the power to the camera.
    qa Camera installation hole (2 positions)
    qs Camera head fixing screw
    First loose the screw and face the camera head to the desired direction,
    then tighten the screw to fix it.
    qd MONITOR output jack
    Connect to a video input connector of a monitor. You can adjust the
    camera while looking at the image on the monitor. After adjusting the
    camera, disconnect the cable.
    Pin No. Pin name
    1 Sensor In +
    2 Sensor In – (GND)
    3 Alarm Out 1 +
    4 Alarm Out 1 –
    5 Alarm Out 2 +
    6 Alarm Out 2 –
    DC 12V
    AC 24V
    I / O
    qf LAN port (RJ45)
    Connect to a hub or computer on the 10BASE-T or 100BASE-TX
    network using a network cable (UTP, category 5).
    qg I/O (Input/Output) port
    This port is provided with a sensor input and two alarm outputs.
    Pin assignment of I/O port
    For details on each function and required settings, see the User’s
    Guide stored in the supplied CD-ROM.
    For wiring, see “Connecting the I/O port”.
    qh 12V DC/ 24V AC (power input) connector
    Connect to a 12V DC or 24V AC power supply system with the
    supplied AC power cord.
    qj 5 (line output) jack (minijack, monaural)
    Connect a commercially available speaker system with the built-in
    qk m (microphone input) jack (minijack, monaural)
    Connect a commercially available microphone.
    ql T (video output) connector (BNC type)
    Outputs a composite video signal. Connect to a composite video
    input connector of a video monitor, VCR, etc. Use the supplied
    monitor cable for connection.
    w; Screw hole for wire rope
    Monitoring the Camera Image
    Install and connect the camera properly following the instructions in this
    manual, then operate the camera referring to the User’s Guide
    contained in the supplied CD-ROM.
    (continued on the reverse side)
Sony SNC-CS50N

Precisa de ajuda?

Número de perguntas: 0

Você tem alguma dúvida sobre o Sony SNC-CS50N ou precisa de ajuda? Faça sua pergunta aqui. Forneça uma descrição clara e abrangente do problema e sua pergunta. Quanto mais detalhes você fornecer para seu problema e pergunta, mais fácil será para outros proprietários de Sony SNC-CS50N responderem adequadamente à sua pergunta.

Veja o manual do Sony SNC-CS50N aqui, de graça. Este manual está na categoria Câmeras de vigilância e foi avaliado por 1 pessoas com uma média de 9.5. Este manual está disponível nos seguintes idiomas: Inglês. Você tem alguma dúvida sobre o Sony SNC-CS50N ou precisa de ajuda? Faça a sua pergunta aqui

Sony SNC-CS50N especificações

Marca Sony
Modelo SNC-CS50N
Produto Câmara de vigilância
EAN 27242684195
Língua Inglês
Tipo de arquivo PDF
Resolução Máxima 768 x 494 pixels
Ângulo de visão (horizontal) 94 °
Intervalo de rotação 94 - 35 °
Iluminação mínima 0.4 lx
Sistema de lente
Comprimento focal 2.9 - 8 mm
Microfone incorporado Não
Rácio Signal-to-Noise (SNR) 50 dB
Gestão de energia
Power over Ethernet (PoE) Sim
Consumo de energia (típico) 9 W
Tipo de fonte de alimentação PoE
Modo noturno
Versão noturna Sim
Pesos e dimensões
Peso do produto 880 g
Requisitos do sistema
Memória RAM mínima 256 MB
Outras características
Sistemas operativos compatíveis - Microsoft Windows 2000/ XP
Alimentação DC 12 V
Portas E/S - Sensor in x 2\n- Alarm out x 2
Condições ambientais
Temperatura de funcionamento 0 - 50 °C
Limite de temperaturas (armazenamento) -40 - 60 °C

Perguntas Frequentes

Abaixo, encontrará as perguntas mais frequentes sobre Sony SNC-CS50N .

A sua pergunta não está na lista? Faça a sua pergunta aqui