Manual de instruções AMX CCD-15APS-1

AMX CCD-15APS-1
(1)
  • Número de páginas: 4
  • Tipo de arquivo: PDF
RF Plug-In Modules
Dimming Module : CCD-3PD-1
Appliance Module: CCD-15APS-1
120 V
50 / 60 Hz
Typical Power Consumption*: 0.3 W

Installation Instructions

Please Read Before Installing

Installation

Dimming Module Operation

Troubleshooting Guide

Lutron Elec tron ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Print ed in the U.S.A. 1/11 P/N 044-275 Rev. A
Load Specifications:
Control Load Type Min. Load Max. Load
3PD-1
Incandescent, Halogen 10 W 300 W
MLV 10 W / VA 200 W / 300 VA
CFL, Fluorescent, ELV
(Switching Mode Only)
10 W 300 W
15APS-1 General purpose None
1/2 HP
††
15 A
Technical Assistance:
U.S.A. / Canada: 1.800.523.9466 Fax +1.610.282.6311
Mexico: +1.888.235.2910
Other Countries: +1.610.282.3800
24 hours a day, 7 days a week.

Important Notes

WARNING - Entrapment Hazard - To avoid the risk of entrapment,
serious injury, or death, these controls must not be used to control
equipment which is not visible from every control location or which
could create hazardous situations such as entrapment if operated accidentally.
Examples of such equipment which must not be operated by these controls
include (but are not limited to) motorized gates, garage doors, industrial doors,
microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure
that the equipment being controlled is visible from every control location and that
only suitable equipment is connected to these controls. Failure to do so could
result in serious injury or death.
NOTICE: To avoid overheating and possible damage to other equipment, do
not use -3PD-1 to control motor-operated or transformer-supplied appliances or
other non-lighting loads. Always use a light bulb that remains within the wattage
rating of the light fixture.
Codes: Install in accordance with all local and national electrical codes.
Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),
0% to 90% humidity, non-condensing. Indoor use only.
Cordset: The cordset has a plug on a 24 in (610 mm) cord and a receptacle on
a 6 in (152 mm) cord.
Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical
cleaning solutions.
Load Type: The -3PD-1 is designed to dim one incandescent, magnetic low-
voltage, or tungsten halogen table or floor lamp. The -3PD-1 can be configured to
switch a compact fluorescent, fluorescent, or electronic low-voltage load. Use with
lighting loads only. Do not use to control a lamp that contains an integral dimmer
or a touch lamp. For a lamp with an integral 3-way switch, the switch should be set
to full on position. The -3PD-1 may not work with dioded light bulbs. Always use
a load that complies with the Load Specifications table above. Always use a light
bulb that remains within the wattage rating of the light fixture.
The -15APS-1 is designed to switch general purpose loads (lighting, non-lighting,
motor-operated, or transformer supplied appliances). Total connected load can
not exceed 1/2 HP, or 15 A.
Low-voltage Applications: The -3PD-1 can be used with magnetic (core
and coil) low-voltage transformers in both dimming and switching modes.
Use with electronic (solid-state) low-voltage transformers in switching mode
only. Operation of a low-voltage circuit with light bulbs inoperative or removed
may result in transformer overheating and premature failure. Lutron strongly
recommends the following:
a. Do not operate low-voltage circuits without operative light bulbs in place.
b. Replace burned-out light bulbs as soon as possible.
c. Use transformers that incorporate thermal protection or fused transformer
primary windings to prevent transformer failure due to overcurrent.
RF Device Placement: RF Plug-In Modules must be located within 30 ft (9 m)
of an RF signal repeater. For systems with an RF signal repeater, RF Plug-In
Modules cannot be controlled by the system until they are programmed in a
system according to the system Setup Guide.

English

Lutron and the sunburst logo are registered trademarks and Clear Connect is a trademark of Lutron Electronics Co., Inc.
©2011 Lutron Electronics Co., Inc.
120 V 50 / 60 Hz
®
COOPERSBURG, PA 18036 USA
I
H
300 VA /
200 W
300 W
1. Place the Plug-In Module in a convenient and accessible
location.
2. Turn the load ON and unplug the cord from the wall outlet.
3. Plug the load cord into a Plug-In Module receptacle.
4. Insert the plug of the Plug-In Module into the wall outlet
5. Turn the Plug-In Module ON.
6. Verify operation. See Dimming Module Operation and
Appliance Module Operation.
WARNING - Shock Hazard - To avoid the risk of
electrical shock, unplug the Plug-In Module when
changing light bulbs. Changing light bulbs with the
power on could result in personal injury or death.
WARNING - Shock Hazard - To avoid the risk of
electrical shock, do not open, cut cord, or rewire the
Plug-In Module. Modification of the module can result
in personal injury or death.
NOTE: -3PD-1 contains a

POLARIZED cord set. It

has a polarized plug (one blade is wider than the other) and
receptacle (one slot is wider than the other).
The polarized plug is not intended to be mated with non-
polarized outlets (having both slots the same size).
The polarized receptacle is intended to mate with a polarized
plug in only one way (the wider slot with the wider blade).
Status LEDs (1-7)
Indicate light level; glow softly as night light when load
is OFF
Toggle Button
Press to toggle ON / OFF; double-tap for full ON; press
and hold while ON for delayed long fade to OFF.
Raise Button
Press to brighten
* Typical Power Consumption test conditions: load is off.
Lower Button
Press to dim
Use these instructions to install the model numbers listed above. For system Setup
Guide and tools visit www.lutron.com
CCD-3PD-1 (1 receptacle) CCD-15APS-1 (1 receptacle)
Plug-In Module
Plug-In Module Receptacle
Plug-In Module
Plug
120 V 50 / 60 Hz
1/2 HP 15 A
®
COOPERSBURG, PA 18036 USA
Status LED
Indicates load status; glows softly as night light when
load is OFF
Toggle Button
Press to toggle ON / OFF.

Appliance Module Operation

I
H
1. Tap the toggle button to turn off the load.
2.
Press and hold the toggle and lower buttons for 3 seconds until
LED 1 flashes to enter Advanced Programming Mode (APM).
3. Tap the raise button until LED 7 flashes.
4.
Press and hold the raise button until LEDs 1 and 3 flash.
5. Tap the toggle button once, wait 2 seconds, then tap the
toggle button again. Notice the LEDs that flash: LEDs 1 and 7
(Dimmer mode - Default), LEDs 2 and 7 (Switch mode).
6. Tap the raise button once. LEDs 2 and 7 will flash and the
module will be in switch mode.
7. Press and hold the toggle button for 6 seconds to save this
setting and exit APM.
NOTE: To change module back to dimmer mode, repeat steps
1-7 and select LEDs 1 and 7 in Step 6.
NOTE: If desired, the Dimming Module can be configured to
function as a switch for lighting loads only.
NOTE: During programming, the Plug-In Modules turn loads
ON/OFF very quickly. Unplug sensitive loads before proceeding.

Advanced Programming (Dimming Module to

switch mode)

1
3
7
2
Symptom Probable Cause and Action
Load does
not turn ON,
but LEDs on
the Plug-In
Module are ON
Load is turned OFF
Turn the power switch on the load to the full
ON position.
Light bulbs are burned out or not installed
Replace or install light bulbs.
Dioded light bulbs
Replace with non-dioded light bulbs.
Load does not
turn ON, and
LEDs on the
Plug-In Module
are OFF
Circuit breaker is OFF or tripped
Turn circuit breaker ON.
Cord is not plugged in
Plug cord into wall outlet as shown in Installation.
Load turns
ON and OFF
continuously
Load is less than minimum load requirement
Make sure the connected load meets the
appropriate minimum load requirement. See
Load Specifications.
Dimming
Module does
not dim
properly
Lamp has an integral dimmer
Use lamp without an integral dimmer.
3-way switch on lamp is not set to full ON
Turn 3-way switch on lamp to full ON
Plug-In Module
is warm
Solid-state control dissipation
Plug-In Modules dissipate a small percentage
of the total connected load. It is normal for
the Plug-In Module to feel warm to the touch
during operation.
Appliance
Module
automatically
turns off
Over temperature condition
Move Appliance Module to a cooler location
and / or reduce the load, then unplug and plug
the Appliance Module into the wall outlet.
Plug-In Module
doesn’t
respond to
a keypad,
wireless
controller, or
sensor
Improper programming
Program according to the system Setup Guide.
Out of RF range
Reposition to be within 30 ft (9 m) of an RF
signal repeater.
Already at current level
The Plug-In Module has already responded to a
command, or is already at the requested setting.
Wireless controller or sensor batteries low or
installed incorrectly
Replace or install batteries properly.
RF inteference
Do not run Plug-In Module cords with other
power cords or communication wires (i.e.
networking, audio, or video signals).
Note: Refer to the system Setup Guide for additional troubleshooting
suggestions.

Returning a Plug-In Module to Factory Settings

Note: Returning a Plug-In Module to its factory settings will remove it
from the system and erase all programming.
Note: Unplug all switched loads from the Plug-In Module prior to
returning to factory settings.
Step 1 : Triple tap the toggle button on the Plug-In Module. DO NOT
release after the third tap.
Step 2 : Keep the toggle button pressed on the third tap (for
approximately 3 seconds) until the LED(s) on the
Plug-In Module scroll up and down or flash quickly.
Step 3 : Release the toggle button and immediately triple tap it again.
The LED(s) on the Plug-In Module will scroll up and down or
flash slowly.
The Plug-In Module has now been returned to factory settings and needs
to be reprogrammed into a system.

Warranty:

For warranty information, please see the enclosed Warranty, or visit
www.lutron.com/resiinfo
NOTE: Advanced Programming of a Plug-In Module requires
access to the module. Do this BEFORE installing if the module
will be hard to reach once installed. No load is required. You
may use any wall outlet within RF range.
Some low wattage loads may try to start when the Appliance Module is OFF due to 0.5 mA leakage
current through the module, similar to a night lighted toggle switch. Consult the load manufacturer for
compatibility.
††
Peak horsepower is not reflective of the UL® appliance horsepower rating. Consult appliance
manufacturer for UL horsepower rating.
Load Cord
Wall Outlet
AMX CCD-15APS-1

Precisa de ajuda?

Número de perguntas: 0

Você tem alguma dúvida sobre o AMX CCD-15APS-1 ou precisa de ajuda? Faça sua pergunta aqui. Forneça uma descrição clara e abrangente do problema e sua pergunta. Quanto mais detalhes você fornecer para seu problema e pergunta, mais fácil será para outros proprietários de AMX CCD-15APS-1 responderem adequadamente à sua pergunta.

Veja o manual do AMX CCD-15APS-1 aqui, de graça. Este manual está na categoria Reguladores de intensidade de luz e foi avaliado por 1 pessoas com uma média de 7.5. Este manual está disponível nos seguintes idiomas: Português, Espagnol, Inglês. Você tem alguma dúvida sobre o AMX CCD-15APS-1 ou precisa de ajuda? Faça a sua pergunta aqui

AMX CCD-15APS-1 especificações

Geral
Marca AMX
Modelo CCD-15APS-1
Produto Regulador de intensidade de luz
Língua Português, Espagnol, Inglês
Tipo de arquivo PDF
Desempenho
Tipo Regulador de luz e interruptor
Design
Design da caixa Externo
Tipo de controlo Não disponível
Cor do produto Branco
Certificação cUL, UL, FCC, IC, SCT, NOM (-3PD only; -15APS pending)
Gestão de energia
Voltagem de entrada AC 120 V
ver mais

Perguntas Frequentes

Abaixo, encontrará as perguntas mais frequentes sobre AMX CCD-15APS-1 .

A sua pergunta não está na lista? Faça a sua pergunta aqui